ブログに戻る
商品レビュー 2026-11-15 Supergrit Abrasives 0 ビュー

Ceramic 3M 747D Sleeve FAQ: Sizes, Grits, and Setup

Ceramic 3M 747D Sleeve FAQ: Sizes, Grits, and Setup

Straight answers on the 3M 747D ceramic abrasive sleeve: what 2" x 1" means, how 60X, 80X, and 100X differ, and how a sleeve compares to a spiral band.

The sleeve these answers refer to

  • CERAMIC 3M (747D) SLEEVE: CERAMIC 3M (747D) SLEEVE is offered in a 2" X 1" size with selectable grits of 60X, 80X, and 100X. These are the two options you actually choose at checkout: dimensions and grit. Everything below hangs off those two facts.
    CERAMIC 3M (747D) SLEEVE
    CERAMIC 3M (747D) SLEEVE

Size and fit questions

What do the 2" x 1" dimensions mean on this sleeve?
The supplied record lists the sleeve as 2" X 1". Those are the only dimensions given, so treat them as the number to match against your drum or spindle before ordering. The catalog does not state which dimension is length and which is diameter, so measure your existing sleeve or drum rather than assuming.
Will it fit my sanding drum?
Only if your drum takes a 2" x 1" sleeve. The supplied information does not list compatible drum brands, arbor sizes, or expansion ranges, so the safe check is to compare your current sleeve's measurements with 2" x 1". If your drum uses a different size, this sleeve is not the match.
Can I choose a different size?
No. Dimensions are a selectable option in the listing, but the only size in the supplied evidence is 2" X 1". Grit is the option that actually varies across the three variants.

Grit questions

Which grits are available in the 747D sleeve?
Three: 60X, 80X, and 100X. Each is a separate variant at the same 2" x 1" size, so the grit is the only thing that changes between them.
Which grit should I start with?
Use the numbering as your guide: 60X is the coarsest of the three and 100X the finest. Start with the coarsest grit that suits the work in front of you, then move to a finer grit if you need a cleaner surface. The catalog does not publish recommended materials or speed settings for each grit, so let your test pass on scrap decide.
Do I need all three grits?
Not necessarily. A single grit is enough if you have one job and one finish target. Buying 60X, 80X, and 100X together makes sense when you expect to step through a sequence on the same part. The listing prices each sleeve individually, so you can build the set you need rather than a fixed pack.

Use and comparison questions

How is a sanding sleeve used on a drum?
A sleeve slides over a matching drum or spindle and is held there while the tool turns. The supplied record does not include mounting steps, operating speeds, or safety instructions, so follow your drum tool's own manual for mounting and speed. Do not improvise a fit: if the sleeve does not seat on the drum at 2" x 1", it is the wrong size.
Is this a ceramic abrasive sleeve, and does that matter?
Yes, the product name identifies it as ceramic, and the 747D designation is part of the product identity. The supplied information does not include performance claims, comparisons to other abrasives, or recommended materials, so the honest position is that ceramic is the abrasive type named here, not a promise about a specific job.
Abrasive sleeve vs spiral band: what is the difference?
A sleeve is a pre-formed 2" x 1" cylinder that fits a matching drum. A spiral band is a strip wound around a spindle, and its fit depends on the spindle and the wrap rather than a fixed sleeve dimension. The supplied record covers only the sleeve, so it cannot confirm spiral band dimensions or interchangeability. If your tool is set up for spiral bands, check that tool's requirements before switching to a sleeve.
Is the 747D sleeve a good choice for metal?
The catalog does not state which materials this sleeve is intended for, so it does not confirm a metal-specific use. What it does give you is a ceramic abrasive in 60X, 80X, and 100X at 2" x 1". If you plan to use it on metal, test on a scrap piece first and follow your tool's guidance for the material.

What the supplied information does not confirm

The record gives dimensions, grit options, and the ceramic identification. It does not give maximum operating speed, backing or backing attachment type, recommended materials, or drum compatibility. Treat those as questions for your tool's documentation, not as gaps you can fill by assumption.

One practical consequence: order by size and grit, and verify fit against your own drum before committing to a quantity. At USD 0.68 per sleeve against a USD 0.90 comparison price, the cost of trying a single grit first is low.

関連記事

Customer Service
ホーム
商品
カート
マイページ